728x90-a1

Miniatur Wunderland official tutorial largest model railway railroad of the world

For 10 years now, the world’s largest model railway can be found in Hamburg’s historic warehouse district a mammoth miniature project. It took 500.000 working hours to create this incredible miniature world on 1.300m². The city’s most popular tourist attraction fascinates over one million people a year. And it’s continually growing!.

Eight different sections, connected by 13 km of track installation, provide an unforgettable experience for all ages. Tons of steel, wood and plaster form the foundation of this extraordinary exhibition. The journey leads through Scandinavia to Germany, from Austria to Switzerland and far away to America in just a few moments. Each day, 900 trains with 12.000 wagons travel a distance of several hundred kilometres.

The longest train is 14.51 metres long. On the North East Sea, with a water capacity of 30.000 litres, large and small ships are cruising. In Scandinavia, America, at the airport and in the cosy fictional town of Knuffingen, 250 computercontrolled vehicles are on the move.

Special attractions are the fire runs, controlled by a sophisticated software. The fire brigades are constantly engaged in fire fighting procedures. But the police are also busy tracking down traffic offenders. The newest attraction of the Miniatur Wunderland is the quot;Knuffingen Airportquot;. After six years of development and a cost of 3.5 million Euro, the world’s probably smallest commercial airport opened in May 2011 On 150 square metres, with more than 40 airplanes and the ground staff that goes with it, it may be the world’s most advanced flight simulation.

From the technology hangar to the air terminal every little detail has been faithfully recreated. Without a doubt, the attention to detail is at the heart of the layout. Over 200.000 figures show life in all its facets. It’s a world where the law chases criminals and where some don’t really care. Where the fire department puts out a large fire and a new fire starts not too far away.

Funeral oration or celebration, Eat or be eaten, Travelers from this or another world, Imagination knows no bounds in the the Wunderland. There are firebreathers,.

Travelling animals and surprisingly strong girls in a world alternating between hectic and peaceful, between wild animals and some that were already tamed, there are hunters and some just hunting for the best pictures,.

How To Build A Rocket From Scratch

For this project I’m going to show you how to build a rocket, from scratch. These homemade “Randomizerâ€� rockets, launch over 1,000 feet high, and eject a little parachute to bring them safely back to the ground. They’re reloadable and relaunchable. And you might even be able to build one, with things around your house. For this project you’re going to need a bottle of gas relief pills, and a plastic champaign glass, like the kind you’d get at the dollar store. Pushing the bottle into the glass, you can see they make a perfect fit, and you’ll see why that’s important in just a few minutes.

Now plastic champaign glasses usually come in packs of two for a buck, but they don’t always look like this one. Some have slightly different textures, or extra decorations for special occasions. But with a little ingenuity, you can probably make any variation work. Now you might have already guessed, this is going to be the nosecone for the rocket. And we don’t need the base, so let’s go ahead and chop it off now, with something like a hacksaw. Make sure to leave about half an inch at the tip, then find a sheet of sand paper, so you can carefully begin sanding the plastic stub down, until it follows the contour of the glass.

I’m using 150 grit sandpaper, and after a couple of minutes, you can already see the nosecone starting to take shape, and looking a lot more aerodynamic. Now if you go one step further, and sand the whole thing with 400 grit, it’ll help the paint stick better. But either way, before you paint the nose cone, it’s a good idea to rough up the inner wall, near the top. Roughing it up now, will save you a step, when we attach it to the rocket later on. Alright it’s time for a paint job, and I went with this yellow gloss spray paint, because it’s made for bonding to plastics, and dries in 15 minutes or less. I recommend going outside and holding it with something like a foam noodle when you spray it,.

Because this way, you don’t make much of a mess. Alright with the nose cone drying, let’s move on to modifying the plastic pill bottle next. You can find these bottles at your local super center, for around 88¢. And if you pull the label slowly and carefully enough, you should be able to get it off without leaving any sticky residue behind. Now we’re only after the empty bottle here, so unless you’re having issues with gas, go ahead and get rid of the pills any way you think is safe. Next you’ll need to carefully, cut the bottom of the bottle, and for that I’m using an Xacto knife. A boxcutter, or pair of scissors will work as well. But whatever you use, the goal here is to cut the edge as straight, and cleanly as possible. Now the threads on the bottle neck have to come off as well, and I found a good tool for removing them is a flat metal file.

Set the bottle on a flat surface and grind away at the threads until they’re flat. But try to keep the bottom ridge, untouched. And while you’re here, go ahead and sand a rough patch into the inner wall of the bottle, like you did for the nosecone, then use 150 grit to rough up the sides of the bottle as well. Alright, let’s move on to building the screwlock, motor mount, next. You’ll just need a 34â€� PVC coupling, which you should be able to find at any hardware store. And it’s important to get the one that has the threads, on the inside. Use your sandpaper to rough up the outside of the casing, then cut 12â€� off the tip, of the threaded end.

This piece will become the “quick connectâ€� adaptor that our sugar motors will screw onto when we’re getting the rocket ready for launch. Now the body tube of the “Randomizerâ€� rocket, is made with a plastic golf club protector, you can find at any sporting goods store. And while you’re out running errands, stop in at the dollar store for a roll of wrapping paper as well. You don’t actually need the paper though. Just 4â€�, of the the brown paper tube that’s inside it. And one roll, will give you nine of them. Alright the next thing we need, is the fin cutting template, which was designed and donated,.

By my friends at SonicDad . And I’ve put a link in the description to where you can get it for free. Go ahead and cut out the “Fin Locationâ€� template as well, and wrap it around the golf club tube, then tape it so both ends, meet perfectly together. Now measure 20â€� up from the end of the tube, and use the edge of the paper template as a cutting guide, for making a clean cut. Your body tube should be 20â€� long, and if it is, then rough up the inner walls, of both ends, with 40 grit sandpaper. Now get your 2part epoxy ready, because the time has come, to cement it together.
728x90-a1

Category:

Boat Plans

Leave a Reply